紙板耐破度儀故障排除與維修的問題

下面由杭州紙邦儀器為你們解答：

一、紙板耐破度測定儀機械系統一般性故障 故障現象故障原因分析排除與維修 測試過程中活塞自動返回，試樣未破裂

1. 測試系統油量不足

2. 測試系統滲油

3. 油缸活塞漏油

4. 試樣耐破強度高于儀器測量上限，儀器執行超量程自動保護

1. 補充加注硅油

2. 檢查松動滲油部位并相應處理

3. 更換活塞體上的 O 型密封圈（23.6×3.55，GB3452.1） 活塞動作失控控制活塞行程的光電對管損壞， 行程開關未動作立即停機檢查更換， 之前嚴禁 開機，否則將造成儀器損壞

二、紙板耐破度測定儀測控系統一般性故障 故障現象故障原因分析排除與維修 無顯示，按鍵失靈保險管燒壞、電源開關損壞、電源線接觸不良或松脫更換保險管、更換電 源開關、檢查修理電源線 通電后或使用中亂顯示，按鍵不起作用系統“死機"按“復位"鍵或關斷電源重新開機 按“打印"鍵打印機不動作打印頭連線脫落或接觸不良 打印頭損壞檢查打印線路 更換打印頭 顯示器無顯示或亂顯示，但儀器其他功能正常顯示器連線脫落或接觸不良 顯示器損壞檢查線路 更換顯示器 顯示正常，一部分按鍵不起作用按鍵損壞更換按鍵 顯示正常，電機工作狀態失控電機控制電路故障檢查電路，查明故障并采取相應措施